Sign In | Join Free | My himfr.com
Home > Steel Sheet Slitting Machine >

RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic

    Buy cheap RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic from wholesalers
     
    Buy cheap RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic from wholesalers
    • Buy cheap RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic from wholesalers

    RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic

    Ask Lasest Price
    Brand Name : RISHBIN
    Model Number : RS 3.0-12.0
    Certification : CE
    Price : Negotiable
    Payment Terms : L/C, T/T, Western Union
    • Product Details
    • Company Profile

    RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic

    RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic
    Steel Sheet Slitting Machine​ Introduction
    • Coil cart for uncoiler
    • Single side/ double side uncoiler(support arm stand for single side uncoiler)
    • Leveling/ leveling + shearing stand
    • Loop bridge
    • Side guide stand
    • Single slitting knife/ double slitting knife stand
    • Loop bridge and scrap winder
    • Tension pad stand
    • Recoiler
    • Coil cart for recoiler
    • Electric control system

    Knives:

    These knives partially penetrate the coil stock causing a crack or fracture on both sides of the stock, separating the mults from one another. Rubber stripper rings are also employed depending on the material thickness to attain a good edge so no burr is present that will hinder downstream operations. As the material is slit, the far outside edges of the coil have edge trim.
    Edge trim:
    This edge trim is taken up on a scrap winder. If the material to be slit is extremely thin, a looping pit can be used to take up the varying thickness of the mults as the edge cuts are generally thinner than the center cuts. The thin the material, the longer the lineal footage in the master coil.
    The looping pit will take up the additional volume prior to entering the tension stand. The tension stand is located prior to the recoiler. A tensioning device is needed because the master coil is crowned or larger in diameter in the center of its width than at the edges.

    Without a tension stand, the slit material from the center of the master coil would take up more quickly while the outboard strips would hang loosely. The recoiler is an expanding mandrel type. The recoiler takes up the slit mults. The recoiler mandrel is fitted with an overarm device which is a shaft with separator discs which prevent interleaving of the narrower coil widths.

    The position of the discs are directly in-line with the slitting knives. The finished slit mults are banded on the outside diameter and are pushed off of the recoiler mandrel onto an awaiting coil car or turnstyle.
    Steel Sheet Slitting Machine Specification:
    Model No.RS 3.0-12.0RS 4.0-16.0RS 6.0-20.0
    Coil MaterialCR Coils , HR Coils, S.S Steel Coils, GI Coils, AL Coils, Copper Coils Picking Oil Coils
    Coil Thickness3.0~12.0mm4.0~16.0mm6.0~20.0mm
    Line Speed0~60m/min0~50m/min0-50m/min
    Coil Weight≤30T(35T)≤30T(35T)≤30T(35T)
    Coil I.Dφ508,φ610,φ760mmφ508,φ610,φ760mmφ508,φ610,φ760mm
    Coil O.D≤φ2200mm≤φ2500mm≤φ2500mm
    Strip Width≥100mm≥100mm≥100mm
    Number of Strip5~20≤5≤5
    Slitting Accuracy±1.0mm±1.0mm±1.0mm
    Blade shaftФ320Ф340mmФ360mm
    Electrical Control SystemPLC Automatic controlPLC Automatic controlPLC Automatic control
    COIL/ROLL DETAILSMaterialHR, CR, SS, GI, PPGI,
    Tensile Strengthδb≤550Mpa,δS≤260Mpa
    Coil/Roll thickness6-20mm
    Steel Coil/Roll width600-2500(Max)
    Coil/Roll I.DΦ500-760 mm
    Coil/Roll O.DΦ2500mm(Max)
    Steel Coil/Roll Weight35T(Max)

    Slitter parameters

    knife pivot diameterФ360 mm
    Knife pivot material40Cr
    Blades specificationΦ360mmXφ360mmX20mm
    Blade material6CrW2Si
    Max slit quantity4 pcs (16mm) 8 pcs(8mm)(Customized)
    Width precision≤±0.05mm/2M

    Other parameters

    Power380V/50Hz/3Ph(Customized)
    Line speed0-60m/min
    Capacity450 KW
    Whole line Dimension45m(L)X10m(W)
    Line directionFrom right to left(Face to machine)
    Machine colorBlue
    Quality RS 3.0-12.0 Steel Sheet Slitting Machine For Carbon And Galvanized Simple Hydraulic for sale
    Inquiry Cart 0
    Send your message to this supplier
     
    *From:
    *To: RISHBIN CO., LTD
    *Subject:
    *Message:
    Characters Remaining: (0/3000)